Customer Care Center
1-800-321-4567
Shopping Cart Shopping Cart

Development Tools for 8051 Microcontrollers

8051 Target Boards

Phyton offers a few 8051-based target boards (header boards) supplied with CodeMaster-52 toolset or separately. All Phyton target boards are very simple and inexpensive and include just very basic components allowing the target microcontroller to run and communicate to a JEM emulator. The boards are generally intended to be used either for application software debugging and/or as a "stamp" for mounting on more complex, custom made boards with necessary peripheral components. See the boards below.

TB2-LPC210X (old p/n TS1-LPC210X)
  • Main features:
    • MCU: NXP/Philips LPC2106
    • 2x10 pin ARM-JTAG compatible connector
    • Extension header for the MCU pins
    • User changeable crystal (16 MHz by default)
    • RESET circuit and button
    • DEBUG jumper for JTAG enable/disable
    • BSL jumper for bootloader enable/disable
    • RTCK pullup resistor
    • Push BUTTON with pullup status LED
    • Power plug-in jack
    • Single power supply: 5-9VAC/DC required
    • Alternative power supply input: pin 19 of the JTAG connector allows powering the board from Phyton JEM-ARM
    • Two on-board voltage regulators: 1.8V and 3.3V with up to 800mA current
    • Power supply filtering capacitor
    • Dimensions: ~2-1/2"x 2-1/4" (66x57 mm)
    • Four corner mounting holes
    • Can be ordered with a JEM-ARM emulator at extra $35
TB2-LPC211X (old p/n TS1-LPC211X)
  • Main features:
    • MCU: NXP/Philips LPC2194
    • 2x10 pin ARM-JTAG compatible connector
    • Extension header for the MCU pins
    • User changeable crystal (16 MHz by default)
    • RESET circuit and button
    • DEBUG jumper for JTAG enable/disable
    • BSL jumper for bootloader enable/disable
    • RTCK pullup resistor
    • Push BUTTON with pullup status LED
    • Power plug-in jack
    • Single power supply: 5-9VAC/DC required
    • Alternative power supply input: pin 19 of the JTAG connector allows powering the board from Phyton JEM-ARM
    • Two on-board voltage regulators: 1.8V and 3.3V with up to 800mA current
    • Power supply filtering capacitor
    • Dimensions: ~3"x2-1/3" (70x60 mm)
    • Four corner mounting holes
    • Can be ordered with a JEM-ARM emulator at extra $35
TB2-LPC213X (old p/n TS1-LPC213X)
  • Main features:
    • MCU: NXP/Philips LPC2138
    • 2x10 pin ARM-JTAG compatible connector
    • Extension header for the MCU pins
    • User changeable crystal (16 MHz by default)
    • RESET circuit and button
    • DEBUG jumper for JTAG enable/disable
    • BSL jumper for bootloader enable/disable
    • RTCK pullup resistor
    • Push BUTTON with pullup status LED
    • Power plug-in jack
    • Single power supply: 5-9VAC/DC required
    • Alternative power supply input: pin 19 of the JTAG connector allows powering the board from Phyton JEM-ARM
    • Two on-board voltage regulators: 1.8V and 3.3V with up to 800mA current
    • Power supply filtering capacitor
    • Dimensions: ~3"x2-1/3" (70x60 mm)
    • Four corner mounting holes
    • Can be ordered with a JEM-ARM emulator at extra $45
Third Parties' target boards

A variety of evaluation or header boards based on ARM microcontrollers are available in the market. Any of them, if featured with a standanard 2x10 pin ARM-JTAG compatible connector, can be used with CodeMaster-ARM IDE and JEM-ARM emulator.

Go Back